bldc motor control driver 18V~50VDC 18V~50VDC0-300w Bldc Motor Driver controller
Description:
The JKBLD300 is a high performance, cost-effective 3 phase BLDC motor drive which can provide power output 300VA max. The design is based on advanced DSP technology and feature high torque, low noise, low vibration, PID speed loop, PID current loop, over current protection, over load protection.
JKBLD300 brushless dc driver is suit the following three-phase sine wave power is 300W brushless dc motor speed regulation, can provide an external potentiometer control, external analog voltage control, PC (such as PLC, SCM) PWM speed regulation, and other functions. At the same time the drive have large starting torque, quick start and brake, and positive & negative switching, combination of manual and automatic control.
Suit motors:
| Model |
| Specification | Unit | JK57BLF01 | JK57BLF02 | JK57BLF03 | JK57BLF04 |
| Number Of Phase | Phase | 3 |
| Number Of Poles | Poles | 4 |
| Rated Voltage | VDC | 36 |
| Rated Speed | Rpm | 4000 |
| Rated Torque | N.m | 0.11 | 0.22 | 0.33 | 0.44 |
| Rated Current | Amps | 2 | 3.6 | 5.3 | 6.8 |
| Rated Power | W | 46 | 92 | 138 | 184 |
| Peak Torque | N.m | 0.33 | 0.66 | 1 | 1.32 |
| Peak Current | Amps | 6.8 | 11.5 | 15.5 | 20.5 |
| Back E.M.F | V/Krpm | 7.7 | 7.4 | 7.3 | 7.1 |
| Torque Constant | N.m/A | 0.073 | 0.07 | 0.07 | 0.068 |
| Rotor Inertia | g.c㎡ | 75 | 119 | 173 | 230 |
| Body Length | mm | 47 | 67 | 87 | 107 |
| Weight | Kg | 0.44 | 0.75 | 1 | 1.25 |
| Sensor | Honeywell |
| Insulation Class | B |
| Degree of Protection | IP30 |
| Storage Temperature | -25～+70℃ |
| Operating Temperature | -15～+50℃ |
| Working Humidity | 85% RH |
| Working Environment | Outdoor (no direct sunlight), no corrosive gas, no flammable gas, no oil mist, no dust |
| Altitude | 1000 meters or less |
| | | Model |
| Specification | Unit | JK60BLS01 | JK60BLS02 | JK60BLS03 | JK60BLS04 |
| Number Of Phase | Phase | 3 |
| umber Of Poles | Poles | 8 |
| Rated Voltage | VDC | 48 |
| Rated Speed | Rpm | 3000 |
| Rated Torque | N.m | 0.3 | 0.6 | 0.9 | 1.2 |
| Rated Current | Amps | 2.8 | 5.2 | 7.5 | 9.5 |
| Rated Power | W | 94 | 188 | 283 | 377 |
| Peak Torque | N.m | 0.9 | 1.8 | 2.7 | 3.6 |
| Peak Current | Amps | 8.4 | 15.6 | 22.5 | 28.5 |
| Back E.M.F | V/Krpm | 12.1 | 12.6 | 12.4 | 13.3 |
| Torque Constant | N.m/A | 0.116 | 0.12 | 0.118 | 0.127 |
| Rotor Inertia | Kg.c㎡ | 0.24 | 0.48 | 0.72 | 0.96 |
| Body Length | mm | 78 | 99 | 120 | 141 |
| Weight | Kg | 0.85 | 1.25 | 1.65 | 2.05 |
| Sensor | Honeywell |
| Insulation Class | B |
| Degree of Protection | IP30 |
| Storage Temperature | -25～+70℃ |
| Operating Temperature | -15～+50℃ |
| Working Humidity | <= 85% RH |
| Working Environment | No direct sunlight, non-corrosive gas, flammable gas, oil mist, no dust. |
| Altitude | 1000m or below |
Electrical Specifications:
| Parameter | Min | Rated | Max | Unit |
| Motor Hall Sensor Angle | 120°/240° | |
| DC Power Input | 18 | 48 | 50 | V |
| Drive Current Output | 0 | 15 | 35 | A |
| Suitable Motor Speed | 0 | | 20000 | rpm |
| Hall Sensor Voltage | 4.5 | 5 | 5.5 | V |
| Hall Sensor Current | | 20 | | mA |
| External Potentiometer | | 10K | | Ω |
Connection Definition:
| Mark | Definition |
| DC+/DC- | DC Power Input (DC24V~DC48V) |
| U,V,W | Motor lead wire |
| Hu,Hv,Hw | Hall sensor lead wire |
| REF+ | Hall sensor power supply + |
| REF- | Hall sensor power supply - |
| VCC | External potentiometer power supply + |
| SV | External potentiometer |
| COM | Public (low level) |
| F/R | Direction: High level/CW Low Level/CCW |
| EN | Enable: High Level/Stop Low Level/Run |
| BRK | Quick Brake: High Level/Stop Low Level/Run |
| SPEED | Speed signal output |
| ALARM | Alarm signal output |
Speed Adjustment Instruction: Motor Speed Quick Response Setting:
A. Motor speed adjusted by the internal potentiometer RV OP/CL Connected (user setting):
B. Motor speed adjusted by the external potentiometer PID Closed loop－Motor quick response
C. Motor speed adjusted by analog signal 0V~+5V input OP/CL Disconnected (factory setting):
D. Motor speed adjusted by analog signal 0V~+10V input NO PID Closed loop－Motor normal response
E. Motor speed adjusted by PWM input: Lead Wire Connection:
Pulse duty ratio 10%-90% / Speed linear modulation Take care of the sequence of U,V,W
Pulse rate: 1K-10K/ pulse amplitude 5V
| Indicator | Green | Power indicator |
| | Red | Over-current, hall error |
| | Red flickering | Stall/over-heat/over-voltage protection |
Product Tags:
|
|
Bldc Motor Control Driver 18V~50VDC 18V~50VDC0-300w Bldc Motor Driver Controller Images
|
